File Manager
Organize, structure and access your data through the selection of drivers.
Backups
Create or restore backups of all system settings.
1. In Mordomus iThink Home Menu, press button: Configurations
2. In the Configurations window -> Utilities, press button: Backups
3. In the Backup window:
3.1. Create Data Backup -> Target directory, press button:
3.1.1. In the selection window, select the folder where to save the file and press the button: Ok
3.2. Create Data Backup -> Target directory, press the button: Apply
1. In Mordomus iThink Home Menu, press button: Configurations
2. In the Configurations window -> Utilities, press button: Backups
3. In the Backup window:
3.1. Restore Data Backup -> Load Data File, press button:
3.1.1. In the selection window, select the data file you want to restore and press the button: Ok
3.2. Restore Data Backup -> Load Data File, select the historical Keep activation box (historical day of restoration) or historical backup Apply (historical stored in the backup file);
3.3. Press button: Restore
Nota: The restoration of a backup the Mordomus iThink will restart.
Presence simulation
Feature that allows you to simulate occupancy of the house when it is unoccupied to deter possible intrusions, giving them the realization that in fact there is someone in your home. This simulator can operate in day or night mode, using different equipment for each situation.

The Presence Simulation uses four variables:


- Wich the equipment are used to simulate the presence;


- How many equipment used simultaneously in the simulation;


- Duration in seconds of the simulation;


- Time, in minutes, between simulations.

1. In Mordomus iThink Home Menu, press button: Configurations
2. In the Configurations window -> Utilities, press button: Simulation of Presence
3. In the Presence Simulator window:
3.1. At State, select Active in the activation box to activate the simulator;
3.2. In Active with Alarm, press button: and choose the alarm, when activated, activate this simulator;
3.3. In No. equipment simultaneously press button: and set how many devices you want to use in the simulation. On the numeric keypad, press button:
3.4. In random Duration (seconds), with the buttons: set the minimum and maximum time duration of the simulation. On the numeric keypad, press button:
Note: The duration of the simulator will use a random value between minimum and maximum;
3.5. In random interval simulations (minutes), with the buttons: set the minimum and maximum time between simulations; On the numeric keypad, press button:
Note: The time between simulations that the simulator will use a random value between this minimum and máximo.
3.6. In light sensor, press button: and set which sensor that will provide the level of brightness, which defines whether the simulator operates in day or night mode. Example: iMeteo light;
3.7. In daytime value, press button: and set the brightness level from which, exclusive, the simulator considers work in day mode;
3.8. In daytime Outputs, press button:
3.8.1. In the Output Selection window, select the output(s) (devices) you want to use in the simulator, when it is operating in day mode;
3.9. At night Outputs, press button:
3.9.1. In the Output Selection window, select the output(s) (devices) you want to use in the simulator, when it is operating in night mode;
Note: These modes are defined by the light sensor.
TIP: In the device(s) selection (Output Select), use the filter zone, to easily locate the device (output) you want, filtering them by type, floor and division. Each output (device) can set you the type of action, its duration and execution, if the device permits.
4. In Action press (Off 0%), (100% ON) or % (percentage level) and set the level at which you want the device (output) is activated;
5. Press button: Test, to activate the simulator, according to the definitions and the day / night mode, which may be completed in the simulation button: Stop, which will be available when you start the simulation.
1. In Mordomus iThink Home Menu, press button: Configurations
2. In the Configurations window -> Utilities, press button: Simulation of Presence
3. In the Presence Simulator window:
3.1. Change what you want;
3.2. In day and night Outputs, make the changes you want, using the button: (edit) or (delete).