Get notified on any irregularity. The Mordomus iThink offers the following alarms:

- TECHNICAL - Detects a possible flood, smoke or gas leak;

- INTRUSION - Detects unwanted intruders, breaking glass and break doors and windows,

- TAMPER - Its function is to protect the alarm devices such as sirens, sensors , wiring, etc., so that they are not unduly manipulated or violated. This alarm is constantly active for a constant protection of alarm systems.

1. In Mordomus iThink Home Menu, press button: Alarms
2. In the Alarms window:
2.1. In Technical Alarms press button:
3. In the Technical Alarms window, press button:
3.1. On the alphanumeric keypad give the alarm a description and press button: Ok
4. In Parameters:
4.1. Set the Delay Time to trigger Eletric Valves and Outputs, with buttons:
5. In Notification (configuration of warning systems): Do not forget to set the sound output in: Configurations -> Records -> Áudio
5.1. To be notified by Alert Message sonically, select in State: the activation box Enable;
5.2. In Alert Message (immediate notification of surround sound), press button: and select the audio file you want;
5.2.1. The Selection window choose the audio file you want and press button: Ok
5.3. To be notified through the warning Siren equipment, select in State: the activation box Enable;
5.4. In Siren, press button:
5.4.1. In the Output Selection window choose the siren device and press button: Ok
5.5. To be informed by SMS, in Phone Notification, press button: and fill with the phone number (maximum 4 telephone contacts) .
5.5.1. On the numeric keypad, press button:
5.6. To be informed by email, at Email Notification, press button: and fill in the email address (maximum 4) .
5.6.1. The alphanumeric keypad, press button: Ok
6. In Inputs Detectors (alarm detection sensors):
6.1. In Inputs alarm detectors, press button:
6.2. In Input Selection (sensors), choose the device(s) that will trigger the alarm and press button: Ok
To detection equipment, you can set up your detection time, with delay time or immediately. Detection with time delay imposes a delay after detection, coinciding with the time set in Parameters -> delay time to trigger Eletric Valves and Outputs. Sensors defined as immediate detection, cause a trigger to alarms that are associated immediately after detection.
7. In Eletric Valves and Detection Outputs (controlled equipment that are active in case of shooting of Technical Alarms Example: In case of flooding the overall cutting water Eletric Valve should be closed and can still pick some light points to blink), press button:
7.1. In Output Selection, choose the device(s) that are controlled in the event of alarm trigger and press button: Ok
To each output (device) you can set you the kind of Action and its Duration, if the device allows it.
7.1.1. In Action, press (Off 0%), (flashing), (ON 100%) or % (percentage level) and set the level at which you want the device (output) to be activated,
- The Flashing Warning does not allow the definition of time and the output will maintain the status it had before starting the burst. You should not activate fluorescent lamps or other slow start systems, intermittently. You can only activate the flashing in output type lighting and sockets.
7.1.2. In Length, with buttons: set the time during which the output (device) is active;
TIP:
In the device(s) selection (Input/Output Selection), use the filter zone, to easily locate the device (input or output) you want, filtering them by Type, Floor and Division.
1. In Mordomus iThink Home Menu, press button: Alarms
2. In Alarms window:
2.1. In Intrlusion Alarms, press button:
3. In Intrusion Alarms, press button:
3.1. On the alphanumeric keypad give a description of the alarm and press button: Ok
4. In Parameters:
4.1. Set the Delay Time to Arm, using buttons:
4.2. Set the Delay Time to Disarm, using buttons:
4.3. In Input to Arm/Disarm (continuous touch), press button: and select an equipment (i.e: Switch) to activate or deactivate the alarm.
4.3.1. In Input Selection, choose the equipment(s) that activate or deactivate the alarm and press button: Ok
4.4. In Alarm Code (individual intrusion alarm enable or disable code), press button: and set the code you want;
4.4.1. On the numeric keypad, to save, press button:
4.5. In General Code (common code for Intrusion alarms), press button:
4.5.1. On the alphanumeric keypad, to save, press button:
5. In Notification (configuration of warning systems): Do not forget to set the sound output to: Configurations -> Registers -> Audio
5.1.To be notified sonorously by Alert Message, select in Status: the activation box Activate ;
5.2. In Alert Message (immediate notification via surround sound), press button: and choose the audio file you want;
5.2.1. In Selection window choose the audio file you want and press button: Ok
5.3. To be notified via the warning equipment, Siren, select in Status: the Activate activation box;
5.4. In Siren, press button:
5.4.1. In Output Selection window choose the siren device and press button: Ok
5.5. To be notified via SMS, In Phone Notification press button: and fill it with phone number (max 4 numbers).
5.5.1. On the numeric keypad, press button:
5.6. To be notified via Email, In Email Notification, press button: and fill with email address(max 4).
5.6.1. On the alphanumeric keypad, press button: Ok
6. In Inputs Detectors (alarm detector sensor, i.e: intrusion sensor, motion, glass break, break-in, among others):
6.1. In Alarms Inputs Detectors , press button:
6.2. In Input Selection, choose the device(s) that activate the alarm and press button: Ok
To detection equipments, you can set the detection time, with delay time or immediately. The detection with time delay, have a time delay after detection wich match with time set on Parameters-> Time Delay to Desarm. Sensors defined as immediate detection trigger a trip to the associated alarms immediately upon detection
7. In Outputs Detection (Devices that must be triggered immediately, when the alarm is detected, Example: Activating a light to deterrence of intruders):
7.1. In Outputs trigger when exist detection, press button:
7.2. In Output Selection window, choose the equipment(s) that are active in case of alarm triggering and press button: Ok
To each output (device) you can define the type of Action and its Duration, if the device allows it.
7.2.1. In Action, press (Off 0%), (Flashing), (On 100%) ou % (percentage level) and set the level at which you want the device to be activated;
- Intermittent Warning does not allow the time setting, and the output will maintain the state it had before it started blinking. Do not operate fluorescent lights or other slow start systems intermittently. It is only possible to activate the flashing in outputs of type lighting and sockets.
7.2.2. In Duration, with buttons:set the time during which the output (device) is active;
8. In Outputs Arm (devices that can be set when the alarm is active, Example: Outdoor lamp that lights momentarily to show you that the alarm was actually active):
8.1. In Outputs to trigger when alarm is armed, press button:
8.2. In Output Selection window, choose the device (s) that informed you of the activation of the alarm and press button: Ok
To each output (device) you can define the type of Action and its Duration, if the device allows it.
8.2.1. In Action, press (Off 0%), (Flashing), (On 100%) ou % (percentage level) and set the level at which you want the device to be activated;
- Intermittent Warning does not allow the time setting, and the output will maintain the state it had before it started blinking. Do not operate fluorescent lights or other slow start systems intermittently. It is only possible to activate the flashing in outputs of type lighting and sockets.
8.2.2. In Duration, with:set the time during which the output (device) is active;
9. In Outputs Desarm (devices that can be set when the alarm is turned off, Example: Outdoor lamp that lights up to show you that the alarm has actually been disabled):
9.1. In Outputs to trigger when the alarm is desarmed, press button:
9.2. In Output Selection window, choose the device(s) that informed you of the disabling of the alarm and press button: Ok
To each output (device) you can define the type of Action and its Duration, if the device allows it.
9.2.1. In Action, press (Off 0%), (Flashing), (On 100%) ou % (percentage level) and set the level at which you want the device to be activated;
- Intermittent Warning does not allow the time setting, and the output will maintain the state it had before it started blinking. Do not operate fluorescent lights or other slow start systems intermittently. It is only possible to activate the flashing in outputs of type lighting and sockets.
9.2.2. In Duration, with button:set the time during which the output (device) is active;
TIP:
In the device(s) selection (Input/Output Selection), use the Filter zone, to more easily locate the device (input or output) you want, filtering them by Type, Floor and Division.
1. In Mordomus iThink Home Menu, press button: Alarms
2. In the Alarms window:
2.1. In Tamper Alarms, press button:
3. In Parameters:
3.1. Set the waiting time for siren activation and outputs, via buttons:
4. In Notification (configuration of warning systems): Do not forget to set the sound output in: Configurations -> Logs -> Audio
4.1. To be notified sonically by message alert, select in State: Enable activation box;
4.2. In message alert(immediate notification of surround sound), press button: and select the audio file you want;
4.2.1. In Selection window choose the audio file you want and press button: Ok
4.3. To be notified through the warning siren equipment, select in State: Enable activation box; ;
4.4. In Siren, press button:
4.4.1. In the Output Selection window choose the siren device and press button: Ok
4.5. To be informed via SMS in phone notification, press button: and fill it with the phone number (maximum 4 telephone contacts)
4.5.1. On the numeric keypad, press button:
4.6. To be informed via email at email notification, press button: and fill in the email address (maximum 4).
4.6.1. On the alphanumeric keypad, press button: Ok
5. In Inputs detectors (alarm detection sensors, for example: the protection circuit connecting leads to the presence sensors, siren and other elements of its alarm system):
5.1. In Alarm Detectors Imputs, press button:
5.2. In the Input Selection window (sensors), the choose device(s) that triggered the alarm and press button: Ok
In detection equipment, you can set up your detection time with time delay or immediately. Detection with time delay imposes a delay after detection, coinciding with the time set in Settings -> Timeout for siren activation and outputs. Sensors defined as immediate detection, cause a trigger to alarms that are associated immediately after detection.
6. In Detection outputs (devices that should be triggered immediately when the alarm is detected):
6.1. In Outputs to trigger when there is detection, press button:
6.2. In Output Selection, choose device(s) that are active in case of alarm trigger and press button: Ok
To each output (device) you can set you the kind of action and its duration, if the device allows it.
6.2.1. In action press (Off 0%), (flashing) (100% ON) or % (percentage level) and set the level at which you want the device (output) is activated;
- The Flashing Warning does not allow the setting time and the output will maintain the status it had before starting the burst. You should not drive fluorescent lamps or other slow start systems, intermittently. You can only activate the flashing in type lighting and sockets outputs.
6.2.2. In Duration, with buttons: set the time during which the output (device) is active;
TIP:
In the device(s) selection (Input/Output Selection ), use the filter zone, to easily locate the device (input/output) you want, filtering them by type, floor and division.
1. In Mordomus iThink Home Menu, press button: Alarms
2. In the Alarms window:
2.1. In the type of alarm you want to change, press button:
3. Select the alarm you want to change;
3.1. You can change the description of the alarm, using button:
4. Then change the behaviors you want in parameters, notification, Inputs detectors, etc ...
1. In Mordomus iThink Home Menu, press button: Alarms
2. In the Alarms window:
2.1. Select the alarm you want and press button: to activate or button to disable
2.1.1. You must enter the respective codes of alarm deactivation/activation .
Note: When entering the general code disables/enables all alarms intrusion type.
1. In Mordomus iThink Home Menu, press button: Alarms
2. In the Alarms window:
2.1. In the type of alarm you want, press button:
3. In the window corresponding to the selected alarm type:
3.1. Select the alarm you want to delete and press button:
1. In Mordomus iThink Home Menu, press button: Alarms
2. In the Alarms window:
2.1. You can view the list of records and alarm events in Event History;
3. To delete the entire list of event log, press button: