The Gas, the Electricity and the water are constantly monitored.

Defines ranges of energetic consumption and optimize actions of control to minimize energy consumption. The consumption control is possible is possible through in three ways:

- Schedule: definition of consumption limits of within the schedule.

- Event: definition of consumption limits when a certain event occurs (Eg: an alarm is activated);

- Always active: definition of constant consumption limits.

The control may be Immediate or Delayed:

Immediate Load Disconnection: allows to create a list of equipments to be disconnected immediately when the maximum consumption it is reached;

Delayed Load Disconnection: allows to create a list of equipments to be disconnected one by one down the list, when the maximum consumption it is reached. It will only jumps to the next device, after ending the delay, but only if the the maximum consumption is still over the limit;

1. At Mordomus Main Menu, press button: Configurations
1.1. Configurations menu press button: Consumption Control
2. At Consumption Control:
2.1. At Meter select the meter you look for;
2.3. At Consumption Policies, press button:
2.3.1. At Consumption Policies window, in Type of Control, press the button: and select the type of control of the Consumption Policy (Continuous, by Event or by Schedule);
2.3.1.1. If you select Continuous:
- At Continuous Control -> At Peak Value (w/h), press button:
- At numerical keyboard type the maximum consumption and press button:
- Press button: Save
2.3.1.2. If you select by Event:
- At Event, press button:and select the type of event;
- At Object Reading, press button: and select the alarm that you want to use to activate the policy;
- At Status, press button:and select the status of that alarm that you want;
TIP: If you select the by Event control, the policy is only applied when the alarm you select in Object Reading and the status that you select in Status: Off/On has happen.
If you select by Input, the politics only is applied when the Input that you selected in Object Reading and the status that you select in Status, has happening.
- Press button: Save
2.3.1.3. If in Type of Control, if you select by Schedule:
- In Days of the Week, select the days where the politics will happen;
- In From: and To: press button: and define the time interval to verify the policy;
- At numerical keyboard, press button:
- At Peak Value, press button:
- At numerical keyboard type the peak consumption, and press button:
- Press button: Save
3. At Control Notification:
3.1. At Surround Sound Notification -> Sound file, press button:
3.1.1. At Selection window, select the audio file that you want and press button: Ok
3.1.2. Select, in Status: Enabled, in order to set the sound notification as active.
3.2. At GSM Notification -> SMS Text, press button:
3.2.1. At alphanumeric keyboard type the message to send as a notification and press button: Ok
3.2.2. Select, in Status: Enabled, in order to set the GSM notification as active.
3.2.3. At MPh1 type the mobile telephone number (maximum of 4 numbers) where to the alert SMS will be sent.
3.2.3.1. At numerical keyboard, press button:
4. At Immediate Load Disconnection:
4.1. At Immediate Outputs (equipments), press button:
4.1.1. At Selection of Output window, select the equipment to disconnect (unload) when the maximum consumption is reached and press button: Ok
TIP: If you want that the unloaded equipment to reconnect again, when the energy consumption gets restored, in Immediate Disconnection -> Immediate Outputs, select the equipment to reconnect and select Reactivate. then press the button: Define, and type in the keyboard the numerical value of the power difference to the Output be reestablished (this value must be lower than the peak value)
5. At Delayed Load Disconnection:
5.1. At Outputs (equipments), press button:
5.1.1. At Selection of Output window, select the equipment to disconnect (unload) when the maximum consumption is reached during X seconds and presses button: Ok
5.2. At Timed Outputs -> Interval (Seconds), press button:
5.2.1. At numerical keyboard, type the value (in seconds) that you wish and press button:
TIP: If you want that the unloaded equipment to reconnect again, when the energy consumption gets restored, in Delayed Disconnection -> Timed Outputs, select the equipment to reconnect and select Reactivate. then press the button: Define, and type in the keyboard the numerical value of the power difference to the Output be reestablished (this value must be lower than the peak value)
1. At Mordomus Main Menu, press button: Configurations
1.1. Configurations menu press button: Consumption Control
2. At Consumption Control:
2.1. At Meter select the meter you look for;
2.2. At Consumption Policies, select the policy to edit and press button:
2.3. At Control Notification, proceed to the modifications that you wish;
2.4. At Immediate load Disconnection and Delayed load Disconnection, press button: and proceed the modifications that you wish.
1. At Mordomus Main Menu, press button: Configurations
1.1. Configurations menu press button: Consumption Control
2. At Consumption Control:
2.1. At Meter select the meter you look for;
2.2. Select the consumer policy to delete and press button:
1. At Mordomus Main Menu, press button: Logger
2. Select Energy
2.1. Filter the information for, Meter, Period and Type of analysis;
2.2. Use the available 3 graphical areas to compare or show 3 meters;
2.3. At Type of analysis you can select the analysis in cost or in energy;
OBS: You should configure the settings Country and Currency, in order to use your correct currency symbol.
1. At Mordomus Main Menu, press button: Energy Resource
2. At Energy Resource window, press: Tariffs
2.1.To define tariffs to electricity meters, press button: Electricity -> Schedule Summer and electricity -> Schedule (s) winter;
2.1.1. At Schedule window:
2.1.1.1. At Weekdays, select the days to define;
2.1.1.2. At From: and To: press button: and define the interval of schedule;
2.1.1.3. At Cost, press button: and define the cost for each Kw/h;
TIP: The Summer schedule is predefined, in case need to edit it, in Summer schedule -> Of - To, press button: and define new dates.
2.2. To define tariffs to Water meter, press button: in Water -> Price of cubic meter and define the Scales and Costs of agreement with your interests;
2.3. To define tariffs for Gas meter, press button: in Gas -> Cost and define the cost;
2.3.1. At numerical keyboard, press button:
1. At Mordomus Main Menu, press button: Energy Resource
2. At Energy Resource window, press: Configuration
2.1. At Status Main Menu - Meter:
2.2. Select the type of energy information to be shown by the widget, Consumption or total Cost;
2.2.1. At Meter Type, press button:and select the type of meter that you wish to provide the energy consumption that Mordomus tries to visualize in home;
2.2.2. At Meter Type, press button:and define the maximum value of the accountant;
2.2.3. At Maximum Scale, press button: and define the maximum value of the accountant;
2.2.3.1. At numerical keyboard, press button:
2.2.4. At Status, it must confirm Activate and like that it is selected. Case you contradict the widget energy, Mordomus will not appear in home.
2.2.5. If in widget energy, to try to visualize the total cost of consumptions, must select the activation Show instinct of the total cost of consumptions.
2.2.6. Press button: Apply
OBS: You should configure the settings Country and Currency, in order to use your correct currency symbol.
1. At Mordomus Main Menu, press button: Energy Resource
2. At Energy Resource window, press: Configuration
2.1. At Currency:
2.1.1. Press button:and select your Country. Automatically Mordomus assumes currency for your Country.
2.1.2. Press button: Apply
OBS: You should configure the settings Country and Currency, in order to use your correct currency symbol.