Be notified in any type of irregularities or intrusions. Mordomus has the following alarms:

- TECHNICAL - It detects a flood, smoke or gas leak;

- INTRUSION - Detects unwanted intruders, break of glasses, doors and windows vandalism, among others;

-TAMPER - Protects the security equipment as: sirens, sensors, security cables, among others, to prevent this systems to be manipulated or violated. This alarm is constantly active for a constant protection of the alarm system.

1. At Mordomus Main Menu, press button: Alarms
2. At Alarms window:
2.1. At Technical Alarms, press button:
3. At Technical Alarms, press button:
3.1. At alphanumeric keyboard give a description to the alarm and press button: Ok
4. At Parameters:
4.1. Defined the Delay time to trigger Electricvalves and Outputs, using buttons:
5. At Notification (configuration of notification systems):
5.1. To be notified through surround sound with an alert message, select in status: Enable
5.2. At Alert message (immediate notification at surround sound), press button: and choose the audio file to use;
5.2.1. At Selection window choose the audio file you wish and press button: Ok
5.3. To be notified through warning equipment, as a siren, select the status: Enable;
5.4. At Siren, press button:
5.4.1. At Output Selection, chooses a siren and press button: Ok
5.5. To be notified by SMS, in Phone notification, press button: and write the mobile telephone number (maximum 4 numbers).
5.5.1. At alphanumeric keyboard, press button:
5.6. To be informed by e-mail, in Email Notification, press button: and write the e-mail address (maximum 4).
5.6.1. At alphanumeric keyboard, press button: Ok
6. At Inputs Detection (alarm detection Inputs):
6.1. At Alarm detection Inputs, press button:
6.2. At Input Selection (sensors), choose the equipment that will activate the alarm and press button: Ok
In detection equipment, it is possible to define the time for detection, with some delay or immediate. The detection with delay, imposes a delay after the detection, which will be the same as the time defined in: Parameters -> Delay time to trigger electricvalves and Outputs. The sensors defined as immediate detection, provoke an immediate activation of the alarms after a detection.
7. At Electricvalves and Outputs of detection (controlled equipments that are activated in case of Technical alarms detection, Example: In case of flood the water main supply electric valve, will be close and you will be able to choose light to blink to warn you for that flood), press the button:
7.1. At Output Selection, choose the equipment that will active in case of shot of alarm and press button: Ok
All output devices can defined the type of actions and your its duration.
7.1.1. At Action, press (Off 0%), (Intermittent), (On 100%) or % (percentage level) and if the device allows define the level that you wish that the device (output) should be activated;
-The intermittent device notice does not allow definition of the time. Also be careful to not intermittent if using florescent lamps or other slow start devices.
7.1.2. At Duration, using button:to define the time duration which the output (device) will be active;
TIP:
At the selection of devices (Output Selection), use the filter zone, to an easier location of the device that you wish, them filtering by Type, Floor and Room.
1. At Mordomus Main Menu, press button: Alarms
2. At Alarms window:
2.1. At Intrusion Alarm, press button:
3. At Intrusion Alarm window, press button:
3.1. At alphanumeric keyboard type a description for the alarm and press button: Ok
4. At Parameters:
4.1. Defined the Delay time to arm, using buttons:
4.2. Defined the Delay time to disarm using buttons:
4.3. At Input to arm/disarm (continuous press), press button: and select an equipment (Eg. Wall switch) to activate or to deactivate the alarm.
4.3.1. At Input Selection, choose the equipment that activate or deactivate the alarm and press button: Ok
4.4. At Alarm Code (code for activation or individual deactivation of intrusion alarms), press button: and define the code that you wish;
4.4.1. At numeric keyboard, to save, press the button:
4.5. At General code (common code for all intrusion alarms), press button:
4.5.1. At numerical keyboard, to save, press button:
5. At Notification (configuration of warnings):
5.1. To be notified through surround sound with an alert message, select in status: Enable
5.2.At Immediate notification of surround sound, press button: and choose the audio file that you wish;
5.2.1. At Selection window choose the audio file that you wish and press button: Ok
5.3. To be notified through warning equipment, as a siren, select the status: Enable;
5.4. At Siren, press button:
5.4.1. At Output Selection choose the siren and press button: Ok
5.5. To be informed by SMS, in phone notification, press button : and type the mobile phone number (maximum 4 numbers).
5.5.1. At numerical keyboard, press button:
5.6. To be informed by e-mail, in E-mail notification press button: and type the email address (maximum 4).
5.6.1. At alphanumeric keyboard, press button: Ok
6. At Detection Inputs (sensors detection of an alarm, Eg. intrusion, motion, glass break, among others:
6.1. At Alarm detection Inputs, press button:
6.2. At Input Selection, chose the equipment that activate with the alarm and press button: Ok
-In detection equipments, it is possible select the time for detection, with a delay or immediate detection The detection with a delay imposes a delay after a detection, which will coincide with the time defined in Configurations -> Delay Time to disarm. The sensors defined as immediate detection, will provoke an immediate alarm detection.
7. At Detection Outputs (device to be activated immediately, when the alarm detects), Eg. activation of a lamp for intruders dissuasion:
7.1. At On-detection Outputs to activate when detection exists, press button:
7.2. At Output Selection, choose a the equipments to activate in case of an alarm and press button: Ok
Every output (device) there can be define the type of action and duration, if the device allows it..
7.2.1. At Action press (Off 0%), (Intermittent), (On 100%) or % (percentage level) and define the level to the one that wishes that the device (output) should be activated;
-The intermittent device notice does not allow definition of the time. Also be careful to not intermittent if using florescent lamps or other slow start devices.
7.2.2. At Duration, through of using buttons:define the time during which the output (device) will be active;
8. At Arming Outputs (devices that can be defined when the alarm is active, Example: Lamp in exterior that it turn on momentarialy was showing that the alrm was really active:
8.1. At On-arming Outputs to actuate when the alarm to arm, press the button :
8.2. At Outputs Selection window, choose or it (s) device (s) that they were imforming about the activation of alarm and preess the button: Ok
Every output (device) there can be define the type of action, and duration if the device or it allows.
8.2.1. At Action (Off0%), (Intermittent), (On 100%) or % (level percentual) and define the level to the one that wishes that the device (output) should be activated;
-The intermittent device notice does not allow definition of the time. Also be careful to not intermittent if using florescent lamps or other slow start devices.
8.2.2. At Duration, through using buttons:define the time during which the output (device) will be active;
9. At Disarming Outputs (devices that canbe defined when the alarm this one deactivated, Example: lamp in exterior that it tur on was showing that the alarm was really deactivated):
9.1. At On-disarming Outputs to actuate when the alarm to disarm, press button:
9.2. At Output Selection window, choose or it (s) device (s) that they were informing about the deactivation of the alarm an press the button: Ok
Every output (device) you could define the type of action, duration, if the device allows it
9.2.1. At Action (Off 0%), (Intermittent), (On 100%) or % (percentage level) and define the level to the one that wishes that the device (output) should be activated;
-The intermittent device notice does not allow definition of the time. Also be careful to not intermittent if using florescent lamps or other slow start devices.
9.2.2. At Duration, through using buttons:define the time during which the output (device) will be active;
TIP:
At selection of it (s) device (s) (Inputs Selection), user the filter zone, easily the device locates (inputs) that you wish, them filtering by Type, Floor and Room.
1. At Mordomus Main Menu, press button: Alarms
2. At Alarms window:
2.1. At Tamper Alarm, press button:
3. At Parameters:
3.1. Defined the time delay activation a siren and outputs, using of buttons:
4. At Notification (configuration of warning systems):
4.1. To be notified through surround sound, select in status: Enable;
4.2. At Immediate notification at surround sound, press button: and choose the audio file that you wish;
4.2.1. At Selection window, chooses the audio file that you wish and press button: Ok
4.3. To be notified with a siren, select in Status: Enable
4.4. At Siren, press button:
4.4.1.At Output Selection, chooses a siren and press button: Ok
4.5. To be notified by SMS, in Phone notification, press button: and write the mobile telephone number (maximum 4 numbers).
4.5.1. At numerical keyboard, press button:
4.6. To be informed by e-mail, in E-mail Notification, press button: and write the e-mail address (maximum 4).
4.6.1. At alphanumeric keyboard, press button: Ok
5. At Inputs Detection (sensors for alarm detection, Example: the protection circuitry of the cables to the sensors, sirens and other elements of your alarm system):
5.1. At Alarm detection Inputs, press button:
5.2. At Input Selection (sensors), choose the equipment that will activate the alarm and press button: Ok
In detection equipment, it is possible to define the time for detection, with some delay or immediate. The detection with delay, imposes a delay after the detection, which will be the same as the time defined in: Parameters -> Delay time to tigger electrovalves and Outputs. The sensors defined as immediate detection, provoke an imediate activation of the alarms after a detection.
6. At Detection Outputs (devices that activate immediately, when an alarm is detected):
6.1. At On-detection Outputs to activate when detection exists, press button:
6.2. At Output Selection, choose a the equipments to activate in case of an alarm and press button: Ok
Every output (device) there can be define the type of action and duration, if the device allows it.
6.2.1. At Action, press (Off 0%), (Intermittent), (On 100%) or % (percentage level) and define the level to the one that wishes that the device (output) should be activated;
- -The intermittent device notice does not allow definition of the time. Also be careful to not intermittent if using florescent lamps or other slow start devices.
6.2.2. At Duration, through using buttons:define the time during which the output will be active ;
TIP:
At selection of it (s) device (s) (selection of output), uses the filter zone, easily to locate the device (output) that you wish, them filtering by Type , Floor and Room.
1. At Mordomus Main Menu, press button: Alarms
2. At Alarms window:
2.1. At type of alarm select the type of Alarm to edit and press button:
3. Select the alarm to edit;
3.1. You can edit the alarm description bay pressing button:
4. Edit the alarm behaviors that you wish in Parameters, Notifications, Inputs, Detectors, etc...
1. At Mordomus Main Menu, press the button: Alarms
2. At Alarms window:
2.1. Select the alarm that wishes and press: to activate ot the button: to deactivate
2.1.1. It is necessary to insert the respective codes of deactivation / activation of alarm.
OBS: When you insert the General code it was deactivating / activating all the alarms of type intrusion.
1. At Mordomus Main Menu, press button: Alarms
2. At Alarms window:
2.1. At type of alarm select the type of alarm to delete and press button:
3. Select the alarm to delete;
3.1.Select the alarm to delete and press button:
1. At Mordomus Main Menu, press button: Alarms
2. At Alarms window:
2.1. You can visualize the list of records related to the alarms;
3. To delete the whole list of the alarms historic, press button: